Skip to content
Emergency
KNOWN FAULTS · Peugeot

Known faults for the Peugeot 2008 (II).

2019–2026 · Petrol / Diesel / Electric

Sources are not verified in real time and no entry confirms that your car is affected.

Buying it used?Which engine has the fewest documented faults, which recalls to ask the seller about and what to look for on the test drive.Before you buy

12 known faults with sources

Engines: 1.2 PureTech (Petrol)

Oil-bath timing belt degradationTiming / lubrication
Engine / equipment
1.0 / 1.2 PureTech (EB2) in the Peugeot 208/2008/308/3008/5008, Citroën C3/C4/C5 Aircross, DS 3, Opel Corsa/Crossland/Grandland
Period mentioned
2012 – approx. 2022
Symptoms
Oil pressure warning, hard brake pedal or reduced assistance, oil consumption, blue smoke, squeal at the front of the engine, turbo whistles or loses power.
Possible cause described
The timing belt runs in oil and degrades (especially with short trips and fuel dilution). Debris clogs the oil pump strainer, the brake vacuum pump filter, the turbo oil feed and the variable valve timing solenoids. Stellantis announced compensation for affected owners in 2025.
Check for the garage
Measure the belt through the oil filler opening with the manufacturer's tool. Confirm whether the vacuum pump campaign was done.
Cost cited in the source
Vacuum pump: €500–800; belt with oil system cleaning: considerably moreA rough figure from the original database, not an up-to-date quote.

Sources from the original database

View full entry

Engines: 1.2 PureTech (Petrol) · 1.5 BlueHDi (Diesel)

Applies if: Only if fitted with the automatic gearbox described in the record.

EAT6/EAT8 jerking and torque converterAutomatic gearbox
Engine / equipment
Aisin EAT6 and EAT8 automatic gearboxes (308, 3008, 5008, 508, 2008, C4 Picasso, C5 Aircross, C4, DS 7, Grandland…)
Period mentioned
2013–2026
Symptoms
Hesitation or a jolt between 1st and 2nd, torque converter shudder in traffic, harsh or delayed shifts and a gearbox fault warning, especially on 2017–2019 3008s.
Possible cause described
Torque converter wear or drift, valve deposits from degraded oil and software faults. Peugeot treats the oil as lifetime, but dirty or low oil causes harsh shifts.
Check for the garage
Check oil level and condition, update the gearbox software at the dealer and, after an oil change, record it with DiagBox and reset the adaptations.
Cost cited in the source
Oil change and update: the most common fix; torque converter or valve body: specialist garage repairA rough figure from the original database, not an up-to-date quote.

Sources from the original database

View full entry

Engines: 1.2 PureTech (Petrol)

Applies if: Only the 1.2 Hybrid 48 V built from 7/6/2023 to 21/1/2026.

Water ingress in the 1.2 Hybrid 48 V belt starter-generatorElectrical and electronic systems
Engine / equipment
1.2 Hybrid 48 V: Peugeot 208 and 2008, Citroën C3, C3 Aircross, C4 and C4 X, DS 3, Opel Corsa, Frontera and Mokka, Jeep Avenger, Alfa Romeo Junior, Fiat 600 and Grande Panda, Lancia Ypsilon
Period mentioned
2023 onwards
Symptoms
Engine or electrical-fault warning light, a hot or burning smell under the bonnet and, in extreme cases, an engine-bay fire.
Possible cause described
There is too little clearance between the petrol particulate filter duct and the 48 V hybrid system’s guard (belt starter-generator): in humid conditions water can get in, an electric arc can form and it can overheat. Stellantis recalled about 700,000 cars worldwide (36 incidents, 12 with fire) and advises against pressure-washing the engine until the repair.
Check for the garage
Check the recall by VIN; do not pressure-wash the engine; with the warning or a burning smell, stop and park outdoors.
Cost cited in the source
Free under the recall.A rough figure from the original database, not an up-to-date quote.

Sources from the original database

View full entry

Engines: 1.2 PureTech (Petrol)

Peugeot 2008 (II) 1.2 PureTech: known faults of the engine according to L'argusEngine
Engine / equipment
1.2 PureTech in the Peugeot 2008 (II)
Period mentioned
2019–2026
Symptoms
Stop & Start stops working; Will not start (up to 04/10/2020); Engine warning light on; Engine warning light on (up to 2021); Engine warning light on (up to 17/02/2021); Oil pressure light on (up to 21/02/2021); Engine warning light on (up to 30/06/2021); Loss of power, oil pressure light and loss of brake assistance from premature timing belt wear (up to 20/06/2022); Oil consumption (up to 21/02/2023); Hard starting; Coolant leak from a porous cylinder head; Engine jerking and judder from carbon build-up, with a risk of engine damage; [1.2 Hybrid (EB2 Gen 3)] "Gearbox fault" message: gears do not engage or the car does not move (up to the end of August 2024); [1.2 Hybrid (EB2 Gen 3)] Engine warning light on (up to 27/12/2024)
Possible cause described
According to the brand's technical notes reported by L'argus (each date shows up to when the affected cars were built): 1) Stop & Start stops working: Earth cable or battery. 2) Will not start (up to 04/10/2020): Starter motor. 3) Engine warning light on: Oxygen sensor (up to 04/07/2022), engine speed sensor or ignition coils. 4) Engine warning light on (up to 2021): Engine control unit, fully covered for cars under 5 years old. 5) Engine warning light on (up to 17/02/2021): Spark plugs with a new part number, or even engine replacement. 6) Oil pressure light on (up to 21/02/2021): Oil pump solenoid valve. 7) Engine warning light on (up to 30/06/2021): High-pressure fuel pump. 8) Loss of power, oil pressure light and loss of brake assistance from premature timing belt wear (up to 20/06/2022): New timing belt and, if needed, oil and vacuum pumps or the whole engine. Warranty extended to 10 years or 175,000 km. 9) Oil consumption (up to 21/02/2023): Oil vapour separator if it uses more than 0.3 l per 1,000 km. Warranty extended to 10 years or 175,000 km. 10) Hard starting: Injector, injector rail or high-pressure pump depending on diagnosis. 11) Coolant leak from a porous cylinder head: Cylinder head to be replaced. 12) Engine jerking and judder from carbon build-up, with a risk of engine damage: Cylinder head cleaning, spark plugs, intercooler, oil separator or engine depending on diagnosis. 13) [1.2 Hybrid (EB2 Gen 3)] "Gearbox fault" message: gears do not engage or the car does not move (up to the end of August 2024): Gear-change mechanism or gearbox to be replaced; fixed under recall MS7. 14) [1.2 Hybrid (EB2 Gen 3)] Engine warning light on (up to 27/12/2024): Camshaft phaser bolt.
Check for the garage
Compare your symptom and your car's build date with this list. If they match, tell the workshop and ask them to check that part first before replacing others. The brand or a warranty extension covers some repairs: ask the dealer with the car's details.
Cost cited in the source
No verified estimate; ask the garage for a quote.A rough figure from the original database, not an up-to-date quote.

Sources from the original database

View full entry

Engines: 1.2 PureTech (Petrol) · 1.5 BlueHDi (Diesel) · e-2008 (Electric)

Peugeot 2008 (II): known faults of the gearbox and transmission according to L'argusGearbox
Engine / equipment
Peugeot 2008 (II), all engines
Period mentioned
2019–2026
Symptoms
[6-speed manual] Hard to engage 5th and 6th (up to 30/09/2020); [6-speed manual] Clutch fluid leak (up to 20/06/2023 on the DV5 diesel and up to 31/05/2023 on the 1.2 petrol); [6-speed manual] Gears jump out (up to 08/02/2024); [6-speed manual] Hard to engage 1st, 2nd and/or reverse (up to 08/02/2024); [EAT8 automatic] Will not start on the 1.2 PureTech; [EAT8 automatic] "Automatic gearbox fault" message
Possible cause described
According to the brand's technical notes reported by L'argus (each date shows up to when the affected cars were built): 1) [6-speed manual] Hard to engage 5th and 6th (up to 30/09/2020): Forks, gears and synchronisers. 2) [6-speed manual] Clutch fluid leak (up to 20/06/2023 on the DV5 diesel and up to 31/05/2023 on the 1.2 petrol): Clutch slave cylinder to be replaced. 3) [6-speed manual] Gears jump out (up to 08/02/2024): Gear selector shaft and cassette. 4) [6-speed manual] Hard to engage 1st, 2nd and/or reverse (up to 08/02/2024): Fork, gears and synchroniser. 5) [EAT8 automatic] Will not start on the 1.2 PureTech: Starter motor to be replaced. 6) [EAT8 automatic] "Automatic gearbox fault" message: Hydraulic block and solenoid valve or complete gearbox to be replaced.
Check for the garage
Compare your symptom and your car's build date with this list. If they match, tell the workshop and ask them to check that part first before replacing others. The brand or a warranty extension covers some repairs: ask the dealer with the car's details.
Cost cited in the source
No verified estimate; ask the garage for a quote.A rough figure from the original database, not an up-to-date quote.

Sources from the original database

View full entry

Engines: 1.2 PureTech (Petrol) · 1.5 BlueHDi (Diesel) · e-2008 (Electric)

Peugeot 2008 (II): known faults of the chassis, steering and brakes according to L'argusSuspension and steering
Engine / equipment
Peugeot 2008 (II), all engines
Period mentioned
2019–2026
Symptoms
Rear crossmember (axle) knocking (up to 04/07/2021); Rear axle noise (up to 25/10/2021); Front axle knocking (up to 29/05/2022)
Possible cause described
According to the brand's technical notes reported by L'argus (each date shows up to when the affected cars were built): 1) Rear crossmember (axle) knocking (up to 04/07/2021): Rectify or replace the protectors. 2) Rear axle noise (up to 25/10/2021): Refit or replace the rear crossmember protectors. 3) Front axle knocking (up to 29/05/2022): Front hub carrier lower ball joint.
Check for the garage
Compare your symptom and your car's build date with this list. If they match, tell the workshop and ask them to check that part first before replacing others. The brand or a warranty extension covers some repairs: ask the dealer with the car's details.
Cost cited in the source
No verified estimate; ask the garage for a quote.A rough figure from the original database, not an up-to-date quote.

Sources from the original database

View full entry

Engines: 1.2 PureTech (Petrol) · 1.5 BlueHDi (Diesel) · e-2008 (Electric)

Peugeot 2008 (II): known faults of the electronics and interior according to L'argusElectrical and electronic systems
Engine / equipment
Peugeot 2008 (II), all engines
Period mentioned
2019–2026
Symptoms
Ignition cannot be switched on (up to 22/09/2020); Water at the front occupants' feet (up to 21/02/2021); Selected temperature is lost after switching off (up to 04/05/2021); Poor reversing camera image (up to 13/11/2021); Front seat lowers by itself (up to 02/03/2022); GPS shows the wrong position (up to 04/05/2022); Connected navigation faults (up to 02/04/2023); Crack in the centre of the driver's airbag cover (up to 30/06/2023); Instrument cluster screen black, or even the touchscreen (up to 01/03/2024)
Possible cause described
According to the brand's technical notes reported by L'argus (each date shows up to when the affected cars were built): 1) Ignition cannot be switched on (up to 22/09/2020): Electric steering lock. 2) Water at the front occupants' feet (up to 21/02/2021): Check the pipes or replace the drain box. 3) Selected temperature is lost after switching off (up to 04/05/2021): Multifunction front panel to be replaced. 4) Poor reversing camera image (up to 13/11/2021): Camera to be replaced. 5) Front seat lowers by itself (up to 02/03/2022): Control to be replaced. 6) GPS shows the wrong position (up to 04/05/2022): GPS aerial. 7) Connected navigation faults (up to 02/04/2023): Software update. 8) Crack in the centre of the driver's airbag cover (up to 30/06/2023): Airbag to be replaced. 9) Instrument cluster screen black, or even the touchscreen (up to 01/03/2024): Radio-frequency supervision unit to be replaced.
Check for the garage
Compare your symptom and your car's build date with this list. If they match, tell the workshop and ask them to check that part first before replacing others. The brand or a warranty extension covers some repairs: ask the dealer with the car's details.
Cost cited in the source
No verified estimate; ask the garage for a quote.A rough figure from the original database, not an up-to-date quote.

Sources from the original database

View full entry

Engines: 1.2 PureTech (Petrol) · 1.5 BlueHDi (Diesel) · e-2008 (Electric)

Peugeot 2008 (II): known faults of the body according to L'argusBodywork
Engine / equipment
Peugeot 2008 (II), all engines
Period mentioned
2019–2026
Symptoms
Parking aids fail (up to 13/09/2020); Tailgate will not open (up to 26/07/2022); Fuel flap will not close (up to 16/01/2023); Rear lights deteriorated around the edge (up to 02/07/2023)
Possible cause described
According to the brand's technical notes reported by L'argus (each date shows up to when the affected cars were built): 1) Parking aids fail (up to 13/09/2020): Harness and/or sensors. 2) Tailgate will not open (up to 26/07/2022): Switch. 3) Fuel flap will not close (up to 16/01/2023): Actuator. 4) Rear lights deteriorated around the edge (up to 02/07/2023): Lights to be replaced.
Check for the garage
Compare your symptom and your car's build date with this list. If they match, tell the workshop and ask them to check that part first before replacing others. The brand or a warranty extension covers some repairs: ask the dealer with the car's details.
Cost cited in the source
No verified estimate; ask the garage for a quote.A rough figure from the original database, not an up-to-date quote.

Sources from the original database

View full entry

Engines: 1.5 BlueHDi (Diesel)

AdBlue system failure (start countdown)Exhaust and emissions (AdBlue)
Engine / equipment
1.5 / 1.6 / 2.0 BlueHDi with AdBlue (Peugeot, Citroën, DS, Opel)
Period mentioned
Approx. 2014 onwards
Symptoms
Emission system fault message and a “starting impossible in X km” countdown, AdBlue/UREA warning and engine light.
Possible cause described
Failure of the AdBlue tank pump module (circuit board, pressure sensor or heater) or of the AdBlue injector. The engine does not stop while driving, but once the countdown reaches zero it will not restart.
Check for the garage
Diagnose with Diagbox or equivalent: AdBlue pressure, flow test and tank temperature.
Cost cited in the source
Complete module or tank: approx. €600–1,500 (estimate)A rough figure from the original database, not an up-to-date quote.

Sources from the original database

View full entry

Engines: 1.5 BlueHDi (Diesel)

1.5 BlueHDi camshaft chainTiming system
Engine / equipment
1.5 BlueHDi (DV5): Peugeot 208/2008/308/3008/5008/508/Rifter, Citroën C3/C4/C5 Aircross/Berlingo, Opel, DS, Fiat
Period mentioned
2017–2023
Symptoms
Rattle from the top of the engine, loss of power; in severe cases the chain breaks and the engine fails.
Possible cause described
The 7 mm chain linking the two camshafts wears prematurely, influenced by soot in the oil. Stellantis replaced it with an 8 mm chain in 2023 and opened an inspection campaign.
Check for the garage
Ask the dealer whether the car is in the campaign (free inspection and replacement if needed) and whether the 8 mm chain is fitted.
Cost cited in the source
€700–1,400 for the chain; €4,000–7,000 if it breaksA rough figure from the original database, not an up-to-date quote.

Sources from the original database

View full entry

Engines: 1.5 BlueHDi (Diesel)

Peugeot 2008 (II) 1.5 BlueHDi: known faults of the engine according to L'argusEngine
Engine / equipment
1.5 BlueHDi in the Peugeot 2008 (II)
Period mentioned
2019–2026
Symptoms
Engine sometimes will not start (up to 15/09/2020); Engine warning light on (up to 15/09/2020); Timing belt noise from oxidation (up to 01/10/2021); Engine warning light on; AdBlue warning light on (up to 31/12/2022); Engine warning light on when cold (up to 31/12/2022); Will not start, knocking, slipped or broken camshaft chain (up to early February 2023); AdBlue leak (up to 26/02/2023); Oil leak between the camshaft carrier and the cylinder head (up to 31/03/2023); Engine noise at idle or under light acceleration (up to 14/10/2023); Loss of power, jerking or will not start (DV5 Euro 6.4)
Possible cause described
According to the brand's technical notes reported by L'argus (each date shows up to when the affected cars were built): 1) Engine sometimes will not start (up to 15/09/2020): Starter motor. 2) Engine warning light on (up to 15/09/2020): Intake air sensor. 3) Timing belt noise from oxidation (up to 01/10/2021): Belt to be replaced. 4) Engine warning light on: Engine harness (up to 31/08/2021) or glow plugs (up to 16/11/2022). 5) AdBlue warning light on (up to 31/12/2022): AdBlue tank to be replaced. Fully covered up to 5 years or 150,000 km, partly from 5 to 8 years or up to 210,000 km. 6) Engine warning light on when cold (up to 31/12/2022): Catalytic converter or particulate filter to be replaced. 7) Will not start, knocking, slipped or broken camshaft chain (up to early February 2023): Camshaft chain and tensioner, timing kit, camshafts and valves. Fully covered up to 7 years or 180,000 km. 8) AdBlue leak (up to 26/02/2023): AdBlue injector. 9) Oil leak between the camshaft carrier and the cylinder head (up to 31/03/2023): Seal and sealing to be rectified. 10) Engine noise at idle or under light acceleration (up to 14/10/2023): Dual-mass flywheel. 11) Loss of power, jerking or will not start (DV5 Euro 6.4): Injection pump and rail, injectors to be replaced.
Check for the garage
Compare your symptom and your car's build date with this list. If they match, tell the workshop and ask them to check that part first before replacing others. The brand or a warranty extension covers some repairs: ask the dealer with the car's details.
Cost cited in the source
No verified estimate; ask the garage for a quote.A rough figure from the original database, not an up-to-date quote.

Sources from the original database

View full entry

Engines: e-2008 (Electric)

On-board charger failure (e-CMP)Charging (on-board charger)
Engine / equipment
e-CMP platform EVs with the Mahle on-board charger: Peugeot e-208, e-2008 and e-Rifter, Citroën ë-C4 and ë-Berlingo, DS 3 E-Tense, Opel Corsa-e, Mokka-e and Combo-e
Period mentioned
2019–2024
Symptoms
AC charging (home or public) becomes erratic, drops from 11 kW to about 7 kW or fails completely with messages such as “Charging paused” or a critical error. DC fast charging keeps working.
Possible cause described
The Mahle on-board charger, which converts AC into DC for the battery, fails. It was fitted to at least ten Stellantis EV models until 2024, when the supplier was changed. There is no recall, but in the Netherlands its warranty was extended from two to four years in 2021, and in Denmark the consumer association FDM obtained a free replacement as a known defect.
Check for the garage
Test charging on a three-phase and a single-phase AC point, read the charger codes with DiagBox and check whether it has already been replaced and by which version. Claim warranty or known-defect treatment before paying.
Cost cited in the source
New charger: approx. €1,100–3,700 (converted from dollars) or about €5,300 at a Danish dealer; often covered by warranty or as a known defectA rough figure from the original database, not an up-to-date quote.

Sources from the original database

View full entry

Engines for this model