Known faults for the BMW Serie 6 (E63/E64).

Engine / equipment

ZF 6-speed automatic 6HP19/21/26/28 (E53, E60/E61, E63/E64, E65/E66, E85, E90–E93)

Period mentioned

Approx. 2001–2013

Symptoms

Oil drips or dampness by the electrical connector on the side of the pan, a bump on the downshift just before stopping, harsh or flared shifts (especially 3rd-4th and 4th-5th under throttle) and a limp mode that clears after restarting.

Possible cause described

The sealing sleeve between the mechatronic unit and the wiring harness has O-rings that harden and let oil out. A BMW bulletin says to replace it only for a real leak, not mere dampness, and warns that fitting it wrongly damages the connector pins and forces a mechatronic replacement. With low fluid the gearbox loses pressure. Harsh shifts can also come from worn solenoids or valve body, not only the sleeve.

Check for the garage

At a garage: read the gearbox codes, check the fluid level with the official procedure (correct temperature and engine running) and look for a real leak at the sleeve and pan gasket. After a fluid or parts change, the garage should reset adaptations. If limp mode persists, check solenoids and valve body before replacing the gearbox.

Cost cited in the source

Sleeve and pan gasket: minor repair. If fluid is lost and the gearbox is damaged, in a US forum case BMW offered a remanufactured gearbox for about $2,800 without fitting.A rough figure from the original database, not an up-to-date quote.

Sources from the original database

Engine / equipment

M57 3.0 six-cylinder diesel with swirl flaps (330d E46/E90, 525d/530d/535d E39/E60, 635d, 730d E65, X3 3.0d, X5 3.0d E53/E70, X6 30d/35d)

Period mentioned

1998–2010

Symptoms

Usually none until it fails. A common early warning: oil seeping around the flap spindles on top of the engine. If a flap or its screw comes loose and enters a cylinder: sudden heavy knocking, loss of power, smoke and possible turbo damage as well.

Possible cause described

The metal flaps in the intake manifold collect soot and oil and their spindles wear over the years. The flap, its screw or part of the spindle can come loose and drop into the cylinder, damaging valves, piston and head. An owners' forum quotes BMW as having strengthened the spindles on later manifolds (from 4 to 4.5 mm), but other owners doubt the change removes the risk.

Check for the garage

At a garage: confirm whether the manifold has swirl flaps (some versions do not), look for oil around the spindles and play in the flaps, and check the history for earlier replacement or removal. With any new metallic knocking, stop the engine and do not restart it.

Cost cited in the source

Preventive inspection: workshop labour. If a flap enters the engine, a buyer's report quotes repair costs above €4,000.A rough figure from the original database, not an up-to-date quote.

Sources from the original database

Engine / equipment

S54 (M3 E46, Z4 M), S65 V8 (M3 E90/E92/E93) and S85 V10 (M5 E60, M6 E63)

Period mentioned

2000–2013

Symptoms

Little prior warning; once wear is advanced, a metallic rod knock that rises with revs. On the S65 and S85, also jerking and limp mode from failing throttle actuators.

Possible cause described

Very tight rod bearing clearances and soft bearing material, made worse by cold oil, revving the engine before it is warm and poor maintenance. Catastrophic failure is rare, but premature wear is common.

Check for the garage

Oil analysis and bearing replacement history. Indicative preventive replacement: S54 around 130,000–160,000 km, S65 around 100,000–130,000 km and S85 around 80,000–110,000 km.

Cost cited in the source

Preventive replacement: approx. €2,800–5,500 (converted from dollars); a spun bearing costs far moreA rough figure from the original database, not an up-to-date quote.

Mileage cited in the database: 80,000–160,000 km. This is not a maintenance interval and does not predict a failure.

Sources from the original database